What are the common causes of the P0713 code on a Jaguar?

cause_transmission_fluid, cause_wiring_damage, cause_connector_corrosion

How much does it cost to fix the P0713 code?

The estimated repair cost for the P0713 code is $100 - $500. This includes parts and labor.

P0713Jaguar XfJahre: 1996 - 2026

Transmission Fluid Temperature Sensor Circuit High Input

Geprüft durch ASE-zertifizierten Techniker

Ist es sicher zu fahren?Driving with a P0713 code can lead to unpredictable transmission behavior, including harsh or delayed shifts, incorrect torque converter lock-up, and potentially transmission overheating if the transmission control module (TCM) cannot accurately monitor fluid temperature. The TCM relies heavily on accurate TFT data for proper shift scheduling, line pressure control, and engagement of the torque converter clutch. Operating the transmission without this critical data can accelerate internal wear, reduce fuel economy, and potentially lead to costly transmission damage over time. It is strongly advised to have this issue diagnosed and repaired promptly to prevent further complications.

Werbefläche (Leaderboard)

Was bedeutet das?

Code P0713 indicates a problem with the transmission fluid temperature sensor.

Haftungsausschluss: Dieser Diagnosecode ist Teil des OBD2-Standards und gilt für Jaguar Xf Modelle von 1996 bis 2026. Bitte beachten Sie jedoch, dass dies von der genauen Motorkonfiguration abhängt.

Werbung (Im Artikel)

Häufige Ursachen

Niedriger, verschmutzter oder verbrannter Getriebeölstand

Beschädigter oder gebrochener Kabelbaum

Korrodierter oder loser Steckverbinder

Zu beachtende Symptome

Motorkontrollleuchte leuchtet
Warnung vor Getriebeüberhitzung
Hartes oder ruckhaftes Schalten

Wie man diagnostiziert

**Step 1: Initial Scan Tool Analysis and Visual Inspection.** Connect a professional-grade scan tool and retrieve all stored and pending Diagnostic Trouble Codes (DTCs). Specifically, monitor the Transmission Fluid Temperature (TFT) sensor live data. A P0713 "High Input" code typically indicates the Powertrain Control Module (PCM) is receiving a voltage signal that corresponds to an extremely low temperature (e.g., -40°F/-40°C) or an open circuit. This is often due to infinite resistance in the sensor or its circuit. Visually inspect the transmission wiring harness, paying close attention to the TFT sensor connector (if external) or the main transmission connector (if internal). Look for signs of corrosion, bent pins, chafing, cuts, or any physical damage that could lead to an open circuit or a short to voltage.

**Step 2: Electrical Circuit Testing at the Sensor Connector.** Locate the TFT sensor. On many modern transmissions, it's integrated into the valve body, lead frame, or an internal wiring harness assembly, requiring the transmission pan to be dropped for access. If accessible, disconnect the electrical connector from the TFT sensor. Using a Digital Multimeter (DMM), measure the resistance across the two terminals of the TFT sensor itself. A "High Input" code strongly suggests an open circuit within the sensor, so you should expect to read infinite resistance (OL) or a resistance value significantly higher than manufacturer specifications for ambient temperature. Next, with the ignition ON (engine OFF), measure the voltage at the harness connector going *to* the sensor. One wire should typically show a 5-volt reference signal from the PCM, and the other should be a ground. A constant 5V on the signal wire, or an absence of ground, could indicate an open circuit in the sensor or its ground path.

**Step 3: Wiring Integrity Check from Sensor to PCM.** With the TFT sensor connector disconnected and the PCM/TCM connector also disconnected (to prevent damage to the control module), perform continuity checks on the wiring harness. Use your DMM to check for continuity between the TFT sensor connector terminals and their corresponding terminals at the PCM/TCM connector. An open circuit on either the signal wire or the ground wire will cause a P0713. Additionally, check both wires for shorts to ground and shorts to voltage (e.g., 12V from another circuit). A short to voltage on the signal wire could also cause a "High Input" condition, as the PCM would interpret the higher voltage as an extremely low temperature or an out-of-range signal.

**Step 4: Advanced Sensor Verification (If Accessible and Wiring Passes).** If the TFT sensor is externally accessible and the wiring tests pass, you can further verify the sensor's function. Place the sensor in a controlled temperature environment (e.g., a cup of water with a thermometer) and measure its resistance at various temperatures. The resistance of a thermistor-type sensor (which TFT sensors typically are) should decrease as the temperature increases. Compare these readings to the manufacturer's resistance-temperature chart. If the resistance remains constant, is always extremely high, or does not change predictably with temperature, the sensor is faulty. If the sensor is internal and all wiring tests pass, the internal sensor itself is the most probable cause, necessitating transmission pan removal for replacement.

Häufige Lösungen

**Replace the Transmission Fluid Temperature (TFT) Sensor:** This is the most frequent solution, especially if the sensor tests open circuit or out of specification. On many vehicles, this sensor is integrated into the internal transmission wiring harness, valve body, or lead frame assembly, requiring the transmission pan to be dropped for access and replacement.

**Repair or Replace Damaged Wiring or Connectors:** If diagnostic steps reveal an open circuit, a short to voltage, or corroded/damaged terminals within the wiring harness or connectors leading to the TFT sensor, these components must be meticulously repaired or replaced to restore proper circuit integrity.

**Address Powertrain/Transmission Control Module (PCM/TCM) Fault:** In rare instances, the PCM or TCM itself could be at fault, either failing to provide the correct 5-volt reference signal or misinterpreting the sensor's input. This should only be considered after thoroughly ruling out the sensor and all associated wiring as the cause.

Join the Discussion

Werbefläche (Bottom Leaderboard)

WerbungSponsor/AdSense

Reparaturkosten

$100 - $500

Ersatzteile$80 - $650

Arbeit$180 - $900

DIY-Schwierigkeitsgrad

Schwierig

Andere beliebte Jaguar Codes

P0108 P0113 P0119

Transmission Fluid Temperature Sensor Circuit High Input

Geprüft durch ASE-zertifizierten Techniker

Wie man diagnostiziert

Häufige Lösungen

Was bedeutet das?

Häufige Ursachen

Zu beachtende Symptome

Wie man diagnostiziert

Häufige Lösungen

Join the Discussion

Reparaturkosten

DIY-Schwierigkeitsgrad

Andere beliebte Jaguar Codes

Scanning Engine...

Was bedeutet das?

Häufige Ursachen

Zu beachtende Symptome

Wie man diagnostiziert

Häufige Lösungen

Join the Discussion

Reparaturkosten

DIY-Schwierigkeitsgrad

Andere beliebte Jaguar Codes